![]() ![]() If anyone has any ideas how to fix that, I'd love to hear them. It always hangs on shutdown which means it always does a scandisk when it restarts. The only problem I have found is it does not close cleanly. And then I used these instructions to get qemu running on the PI.Īfter qemu installed, I used the following command to run 98 on the RPI. And this works much better anyway since the desktop is a much faster PC to work with.Īfter the win98 install, I took the resulting img file and copied it over to the PI. It bypassed all the Win98 installation problems I was having on the RPI. Qemu-system-i386 -localtime -cpu 486 -m 256 -cdrom d win98se.iso -boot d -hda win98.imgĭoing that resulted in a quick, clean, problem-free windows 98 install. Then I used the following command to install windows from a win98 ISO created from an original install disk. That allowed me to do the entire win98 install on the desktop PC.Īfter installing qemu, I used the following command to create the img file: And then I simply ran the apt-get install for qemu. I just installed debian jessie on a desktop PC. Ideally, I would like to use the program launcher from Kodi to do that, but I am open to anything that will get this working simply. I just want to plug in the SD, and boot up, and be able to fire up either of the programs as seamlessly as possible. ![]() I'd prefer Win95 due to the lighter footprint but Win98 would also work. My goal is to set it up so I can use it to run two old car repair programs that I still use regularly. The instructions I have found vary widely about which Linux distribution to use, what emulator to use, how to set it up to install Win95 or Win98, etc. of size: 256MB, 512MB, 1GB, 2GB Mount Floppy disk, CD-ROM or HDD using a GUI. This seems like a pretty common subject from the number of posts about it, but for the life of me I can't find a simple, working set of instructions that is either complete or understandable. Run all retro Pc Sofware (DOS / Win 3.1 / Win 95 / Win98) Run most of. I could pop in an old S3 Trio PCI card and see if I'm right.Does someone have a set of instructions for a relative newbie on how to install and run Windows 95, or Windows 98, in emulation on a Raspberry Pi? I've spent hours searching through this forum and have followed a bunch of threads that have left me frustrated and more confused than when I started. Prior programming experience with ISA and PCI cards tells me that some later cards (S3 Virge PCI for example) tend to switch off legacy VGA mapping logic when the VESA BIOS switches on SVGA modes, so it's possible that real hardware in SVGA modes ignore the VGA chain bit entirely. It's when bank switching and 0xA0000-0xAFFFF are involved the artifacts can happen. Version differences Link Apart from the Demo version, there have been three DOS releases of this game with different video and audio options. It has different puzzles and dialogue compared to the full version. Demo Link A demo can be downloaded here and played using DOSBox. ![]() If I ask Windows 95 to change the driver to "S3 Trio/PCI" then that eliminates the artifacts.Īpparently the generic "S3" driver maintains ISA and PCI compatibility by using SVGA bank switching, while the more specific "S3 Trio32 PCI" driver uses the linear framebuffer. Availability Link This game is not available digitally. ![]() That would also explain why the original Windows 95 driver is subject to whether or not VGA chained mode is active.Īlso, Windows 95 is referring to the card as simply "S3" while Windows 95 OSR2 refers to the card as "S3 Trio/PCI". Switching graphics modes, getting Windows 3. The Windows 95 driver appears to use bank switching and 0xA0000-0xAFFFF (legacy VGA memory access), while Windows 95 OSR2 and later use the linear framebuffer at 0圎0000000. I just traced down another reason for graphical glitches in Windows 95 vs OSR2. ![]()
0 Comments
Leave a Reply. |